What this topic covers
Block B of the Red Seal examination, Engines and Supporting Systems: 21 of the 135 questions. It covers RSOS tasks B-5 to B-12, from the base engine to cooling. These are original practice notes, not documents of the Red Seal program. Inspection values come from the National Safety Code standards in force on January 1, 2027 (jurisdictions may vary). Adjustment, torque and clearance values always come from the vehicle manufacturer's service information; the rest describes standard methods of the trade.
Base engine and lubrication (B-5, B-6)
- Four-stroke cycle: intake, compression, power and exhaust, over two crankshaft revolutions.
- Cylinder leakage test: with both valves closed, air at the exhaust pipe means a leaking exhaust valve, at the intake a leaking intake valve, at the crankcase breather or oil filler worn rings; bubbles in the coolant mean a leaking head gasket.
- Crankshaft end play: dial indicator against the shaft end while the shaft is pried forward and back.
- Ring end gap: ring pushed squarely into the cylinder bore, gap measured with a feeler gauge.
- Low oil pressure at hot idle that recovers at higher rpm: worn bearing clearances. A regulator stuck closed raises pressure.
- Priming after bearing work: crank with fuel disabled until oil pressure shows.
Air intake, exhaust and aftertreatment (B-7, B-8)
- Air inlet restriction: a reading above the stated maximum gives low power and black smoke; replace the element and measure again.
- VGT: commanded vane position changes but the actual position does not, lever hard to move: vanes or linkage seized, usually by soot, giving low boost.
- DPF ash: non-combustible residue of oil additives. Regeneration burns soot only, so an ash-loaded filter is cleaned in a DPF cleaning machine or replaced.
- DEF crystals: washed off with water, then the injector, its seal and line connections are checked.
- Defeated DPF: the vehicle is rejected when any part of the DPF or its regeneration system has been bypassed or defeated (NSC Standard 11B, section 1.3; jurisdictions may vary).
Engine management (B-9)
- Programmable parameters: a setting such as enabling a PTO is changed in software with an electronic service tool (RSOS sub-task B-9.01).
- Sensor types: an NTC thermistor loses resistance as it warms (coolant temperature); Hall-effect and variable-reluctance sensors read position or speed.
- Jumper test: a voltage high code that turns to voltage low with the sensor jumpered proves the harness and ECM input; the sensor is open internally (RSOS sub-task B-9.02).
- Intermittent signal loss: wiggle the harness while watching live data to find a poor connection or chafed harness.
Fuel delivery and engine retarders (B-10, B-11)
- Priming: after new filters, prime and bleed the air as the service information directs.
- Injector cut-out: cutting out a working cylinder lowers engine speed, so no change means that cylinder was not contributing and its injector is tested next (RSOS sub-task B-10.02).
- Fuel-water separator: drained first into a container; the water is disposed of according to jurisdictional regulations.
- Compression brake: opens the exhaust valves near the top of the compression stroke; clearance checked with a feeler gauge, engine positioned as the manufacturer states (RSOS sub-task B-11.01).
- Exhaust brake: closes off exhaust flow to build back pressure. Hydraulic and eddy-current retarders act on the driveline.
Cooling (B-12)
- Freeze protection: a refractometer reads the freezing point and stays accurate for ethylene and propylene glycol; a hydrometer depends on glycol type and temperature.
- Pressure test: a steady engine-off reading rules out external leaks; a needle that pulses with the compression strokes shows combustion gas from a head gasket, liner or cracked head (RSOS sub-task B-12.02).
Sample questions (5)
1. A technician explains the four-stroke diesel cycle to an apprentice. Starting with the piston moving down from top dead centre with the intake valve open, what is the order of the strokes?
- Intake, power, compression, exhaust.
- Intake, compression, power, exhaust.
- Intake, compression, exhaust, power.
- Intake, exhaust, power, compression.
After intake, the air is compressed, the injected fuel burns on the power stroke and the exhaust stroke pushes the burned gas out, over two crankshaft revolutions. Power before compression would fire air that has not been compressed, and exhaust before power, whether after compression or straight after intake, would push out gas that has not yet burned.
2. A technician is about to perform a compression test on a diesel engine with a compression tester in the injector bore. What is done before the engine is cranked?
- Drain the crankcase oil and refill it with the specified fresh oil.
- Remove the valve covers and set the valve lash to specification.
- Remove the air filter element and run the engine at rated speed.
- Bring the engine to temperature and cut off the fuel delivery.
The test is made with the engine warm and fuel delivery disabled, so the starter only turns the engine over and no fuel is injected into the cylinder under test. Changing the oil or resetting valve lash is not part of the test setup, and running at rated speed with the air filter removed draws in dirt, while the readings are taken at cranking speed.
3. A technician performs a cylinder leakage test with the piston at top dead centre on its compression stroke. Air is heard escaping from the exhaust pipe. What is the most likely cause?
- The exhaust valve is not sealing in that cylinder.
- The piston rings are worn in that same cylinder.
- The intake valve is not sealing in that cylinder.
- The head gasket is leaking into the coolant jacket.
With both valves closed, the air pumped into the cylinder should stay in, so air heard at the exhaust pipe passes a leaking exhaust valve. Worn rings send the air to the crankcase breather or oil filler, a leaking intake valve sends it to the intake, and a leaking head gasket shows as bubbles in the coolant.
4. An electronic service tool cuts out each injector in turn on an idling engine. Cutting out cylinder 3 causes no change in engine speed, while the other cylinders each cause a drop. A compression test shows cylinder 3 is within specification. What is the most likely cause?
- The piston rings in that cylinder are badly worn.
- The exhaust valve in that cylinder is badly burnt.
- That cylinder's injector is not delivering fuel.
- The turbocharger is producing too little boost.
No change in speed when a cylinder is cut out shows that cylinder was already contributing nothing. With compression within specification, the fuel side is the remaining cause, so the injector or its drive is not delivering. Worn rings and a burnt valve would have lowered compression, and low boost would affect every cylinder.
5. A technician checks crankshaft end play (axial clearance) with the crankshaft installed in the block. Which tool is used?
- A plastic gauging strip placed across each main journal.
- A dial indicator set against the end of the shaft.
- An outside micrometer used on each main bearing journal.
- A cylinder bore gauge set inside each main bearing bore.
End play is movement along the crankshaft axis, so a dial indicator is set against the shaft end while the shaft is pried forward and back. A plastic gauging strip and a micrometer measure oil clearance and journal diameter, which are radial, and a bore gauge measures bore size, not axial movement.