RedSealTruckExam

Sample questions: Truck and transport mechanic exam

RedSealTruckExam · Topics · Exam guide · Sample questions

Practice questions written by us, with the correct answer and the rule cited. They are not official questions.

1. A shock absorber on a front axle has oil running down the body from the seal, and the ride is bouncy. What is done?

  1. Add oil to the shock absorber through the dust tube.
  2. Tighten the mounting bolts and road test the truck.
  3. Clean the body and return the truck to service.
  4. Replace the shock absorbers on that axle as a pair.

A shock with oil running from the seal has lost its damping, and the shocks on that axle are replaced as a pair so both sides behave the same (RSOS sub-task F-30.02, leaking shocks; NSC Standard 11B, section 2.7, oil leak, jurisdictions may vary). Shocks are sealed units that are not topped up, and tightening the bolts or cleaning the body does not stop the leak.

2. The dash gauges stop sweeping and several modules lose communication when the truck hits bumps. The codes clear after a key cycle. What is the most likely cause?

  1. An outdated software level in the cluster that needs an update.
  2. A failed engine ECM that stays inoperative until it is reprogrammed.
  3. A discharged battery with too little charge to power the data link.
  4. A chafed harness or loose connector that opens briefly in motion.

Faults that appear with movement and clear on a key cycle point to a physical problem such as a chafed harness or a loose connector, so that is found first, for example by wiggling the harness while watching the data (RSOS sub-task D-20.02). A failed ECM or a discharged battery would give a constant fault, and a software level in the cluster would not change with truck motion.

3. A truck derates intermittently over rough roads. The ECM shows an inactive code for the accelerator pedal sensor signal. Which action locates the fault most efficiently?

  1. Wiggle the harness while watching the pedal signal on the tool.
  2. Replace the pedal sensor and road test the truck to see if it returns.
  3. Replace the ECM and load the stored fleet parameters into the new one.
  4. Clear the code and release the truck until the fault becomes active.

An intermittent signal loss points to a poor connection or chafed harness (RSOS sub-task B-9.02), and wiggling the harness while watching live data reproduces and locates it. Replacing the sensor or ECM guesses at the cause and may not fix it, and releasing the truck with the code cleared delays the diagnosis.

4. A technician pulls out the trailer supply valve and applies the service brakes, and air keeps flowing from the trailer service line. What is the most likely cause?

  1. The air dryer purge valve is stuck open and venting.
  2. The tractor protection valve is not closing off the line.
  3. The one-way check valve is not holding the pressure.
  4. The governor is cutting out at too high a pressure.

NSC Standard 11B, section 3A.10 rejects the system when air flows out of the trailer service line with the trailer supply valve closed, which means the tractor protection valve is not shutting off the service line (jurisdictions may vary). A stuck purge valve and a leaking check valve lose tank pressure but do not feed the service line, and the cut-out setting has no effect on the line.

5. An automated transmission is slow to complete shifts and whines in all gears. What is checked first?

  1. Oil level and condition, along with a look for external leaks.
  2. Gear tooth wear on the countershaft, after removing the housing.
  3. Output shaft bearing play, using a dial indicator on the yoke.
  4. Clutch disc thickness, after the transmission is removed.

RSOS sub-task E-24.02 includes checking for external leaks and oil condition. Low or contaminated oil can cause noise and slow shifts, and the check is quick and cheap. Gear wear and clutch disc thickness need the housing opened or the transmission removed, and output shaft bearing play would cause noise at the output, not slow shifts.

6. A shaft seal leaks again after being replaced twice. The technician sees a groove worn in the shaft where the seal lip runs. What is done?

  1. Fit a new seal in the same position and add grease.
  2. Apply anaerobic sealant to the shaft under the seal lip.
  3. Install a thicker seal to cover the worn shaft groove.
  4. Install a wear sleeve on the shaft and fit a new seal.

A groove worn in the shaft is a shaft defect, and one of the repairs listed in RSOS sub-task A-3.05 is installing a wear sleeve to restore the sealing surface. A new seal in the same groove leaks again, sealant on a moving shaft does not form a lasting seal, and a thicker seal does not bridge the groove.

7. A landing gear crank handle turns freely in both speed ranges with almost no resistance, but the legs do not move. What is the most likely cause?

  1. Stripped gears inside the landing gear gear box.
  2. A bent cross tube binding between the two legs.
  3. A lack of grease on the leg tubes and foot pads.
  4. A bent foot pad pressing against the ground.

A crank that spins with almost no resistance while the legs stay put means the gears no longer transmit torque, which is the stripped gear fault listed in RSOS sub-task H-35.02. A bent cross tube, a lack of lubrication or a bent foot pad all cause binding and a hard-to-turn crank, not free spinning.

8. Used hydraulic oil is drained and the spent filters are removed from a lift gate system. How are they handled?

  1. They are poured into the shop floor drain once the oil settles.
  2. They are mixed with shop coolant waste to be picked up later on.
  3. They are recycled or disposed of under jurisdictional regulations.
  4. They are burned in an open barrel set away from the building.

RSOS sub-task J-39.01 requires consumables to be recycled and disposed of according to jurisdictional regulations. A floor drain sends the oil into the sewer, burning it in a barrel releases its contaminants into the air, and mixing it with coolant waste spoils both waste streams for recycling.

9. A driver reports that the windshield fogs with an oily film and the cab smells sweet when the heater is on. The passenger-side carpet is damp. What is the most likely cause?

  1. A plugged cab air filter in the air inlet.
  2. A leaking heater core in the heater box.
  3. A failed blower resistor in the blower housing.
  4. A binding blend door actuator in the heater box.

A sweet smell, an oily film on the glass and damp carpet are the signs of coolant leaking from the heater core into the heater box (RSOS sub-task I-37.02 lists a coolant smell and a steaming windshield as symptoms). A plugged filter reduces air flow without adding moisture. A failed resistor changes blower speed only, and a binding blend door actuator affects temperature control, not coolant leakage.

10. A cooling system pressure test with the engine off holds steady, and there are no external leaks. With the engine running, the gauge needle pulses with each compression stroke and the coolant level keeps dropping. What is the most likely cause?

  1. A weak radiator cap releasing pressure at the overflow tube.
  2. A failed water pump seal leaking at the outside weep hole.
  3. Combustion gas entering the coolant past a gasket or liner.
  4. A stuck-open thermostat letting coolant bypass the radiator.

A steady engine-off test rules out external leaks, and a needle that pulses with the compression strokes shows combustion gas entering the coolant, from a head gasket, liner or cracked head (RSOS sub-task B-12.02 pressure test). A weak cap or a stuck-open thermostat does not make the gauge pulse, and a failed pump seal would show as an external leak.

11. An apprentice has just watched a technician demonstrate a bearing installation. What does the mentor do next?

  1. Give the apprentice the final assessment of the skill.
  2. Have the apprentice practise the skill with guidance.
  3. Demonstrate the same skill a second time without practice.
  4. Move on to an unrelated skill to keep the day varied.

Correct answer: Have the apprentice practise the skill with guidance. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

12. After repairing a chafed sensor harness, a technician clears the stored fault codes. What is done next to confirm the repair?

  1. Operate the engine and verify the code remains inactive.
  2. Disconnect the battery overnight so the ECM relearns its memory.
  3. Replace the sensor so it matches the repaired section of harness.
  4. Release the truck to the customer as soon as the lamp goes out.

Correct answer: Operate the engine and verify the code remains inactive. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

13. With the key on, air pressure is lowered until a test gauge reads 345 kPa (50 psi), but neither the warning lamp nor the buzzer comes on. The bulb is good. What should be checked next?

  1. The governor cut-in setting and its signal line.
  2. The air dryer cartridge and the purge valve.
  3. The compressor discharge line for carbon build-up.
  4. The low pressure warning switch and its wiring.

Correct answer: The low pressure warning switch and its wiring. The full explanation (why this answer is right, why each of the three other options is wrong, and the National Safety Code section it is based on) comes with Premium access.

14. A J1939 data link has intermittent communication. With power off, the resistance across CAN-H and CAN-L at the diagnostic connector reads 120 ohms. What does this reading indicate?

  1. CAN-H and CAN-L are shorted together somewhere along the bus.
  2. An extra terminating resistor has been added inside one module.
  3. One terminating resistor is open, or its connection has failed.
  4. A module on the bus has failed and is loading the bus down.

Correct answer: One terminating resistor is open, or its connection has failed. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

15. A truck's clutch slips under load, and the pedal has no free play left at all. What is the most likely cause?

  1. Disc wear has taken up the clearance at the release bearing.
  2. Cross shaft bushings are worn, so pedal travel is being lost.
  3. The clutch brake is worn, so the input shaft keeps on spinning.
  4. The pilot bearing is seized, so the disc cannot hold its position.

Correct answer: Disc wear has taken up the clearance at the release bearing. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

16. A rear air suspension has a height control valve on each side. After parking overnight, the left side sits much lower than the right side, which is at the correct height. What is done first?

  1. Replace the height control valve on the left side.
  2. Measure the clearance in the torque rod bushings.
  3. Check the left shock absorber mounts for looseness.
  4. Spray soapy water on the left air spring and fittings.

Correct answer: Spray soapy water on the left air spring and fittings. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task and the National Safety Code section it is based on) comes with Premium access.

17. A throttle pedal returns slowly to idle. The pedal pivot is dry and gritty, the return spring is intact, and the position sensor signal is smooth through the full travel. What is done?

  1. Replace the pedal position sensor and clear the codes.
  2. Clean the pedal pivot and lubricate it as specified.
  3. Reprogram the idle speed with an electronic service tool.
  4. Replace the return spring and the pedal assembly.

Correct answer: Clean the pedal pivot and lubricate it as specified. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

18. A diesel reefer engine runs a few minutes and stalls, then restarts after sitting. The fuel filter bowl holds water and there are no codes. What is done?

  1. Replace the fuel injection pump and then clear the stored codes.
  2. Replace the battery and clean the battery cable terminals.
  3. Bleed the cooling system and refill the coolant tank.
  4. Drain water from the tank and filter and replace the filter.

Correct answer: Drain water from the tank and filter and replace the filter. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

19. An air conditioning system has been emptied and a damaged line has been replaced. Before the new charge is added, the technician must check the repair for leaks. What is done?

  1. Pressurize with shop air from the compressor, then check the joints.
  2. Charge the full refrigerant amount, then check joints with a detector.
  3. Pressurize with dry nitrogen, then check joints with soap solution.
  4. Pull a vacuum for five minutes, then charge and watch for frost.

Correct answer: Pressurize with dry nitrogen, then check joints with soap solution. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task and the Federal Halocarbon Regulations section it is based on) comes with Premium access.

20. A technician must replace a leaking hose on the lift cylinder circuit of a dump box. The box is fully lowered and the engine is off. What is done before the fitting is loosened?

  1. The relief valve is backed out to remove the load from the circuit.
  2. The cylinder is pressurized to show where the leak starts.
  3. Stored pressure is released from the circuit in a controlled way.
  4. The reservoir is drained to below the level of the return port.

Correct answer: Stored pressure is released from the circuit in a controlled way. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

21. A hybrid truck shows an isolation fault light. With the system de-energized, an insulation tester reads very low resistance between a high-voltage conductor and chassis. What is the most likely cause?

  1. An open circuit in the high-voltage interlock loop of the system.
  2. Damaged cable insulation or moisture leaking current to chassis.
  3. A discharged auxiliary battery that cannot supply the contactor coils.
  4. A restricted inverter coolant line that is overheating the inverter.

Correct answer: Damaged cable insulation or moisture leaking current to chassis. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

22. A technician must measure voltage in a sensor circuit at a harness connector without damaging the wires or terminals. Which method is used?

  1. Install a breakout harness between the connector halves, then probe it.
  2. Pierce the insulation of each wire with a sharp probe and read the meter.
  3. Force the meter probes into the terminal faces of the connector.
  4. Strip a small section of insulation and tape the meter leads onto it.

Correct answer: Install a breakout harness between the connector halves, then probe it. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

23. With the engine off, a gauge falls 5 kPa per minute with the brakes released, but falls 35 kPa per minute with a full brake application held. Where is the leak most likely?

  1. In a service line or chamber past the treadle valve.
  2. At the governor body or a supply tank fitting.
  3. At the one-way check valve between the tanks.
  4. In the compressor discharge line or the air dryer.

Correct answer: In a service line or chamber past the treadle valve. The full explanation (why this answer is right, why each of the three other options is wrong, and the National Safety Code section it is based on) comes with Premium access.

24. A headlamp is dim. A test light glows normally at the lamp connector and battery voltage is 12.6 V, but a meter reads 10.9 V at the connector with the lamp on. What is done next?

  1. Measure the voltage drop across the supply and ground paths with the lamp on.
  2. Replace the headlamp, because the test light proves the wiring is sound.
  3. Replace the fuse with a higher rating to increase current to the lamp.
  4. Charge the battery to full charge, since 12.6 V is too low for the circuit.

Correct answer: Measure the voltage drop across the supply and ground paths with the lamp on. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

25. A tractor with a synchronized manual transmission jumps out of one gear under engine braking. The linkage is tight and correctly adjusted. What is the most likely cause?

  1. Excessive clutch pedal free play prevents full release.
  2. Worn engagement teeth let the gear slip out of mesh.
  3. A restricted air line delays the range cylinder shift.
  4. A low oil level overheats the synchronizer cone surface.

Correct answer: Worn engagement teeth let the gear slip out of mesh. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

26. A truck pulls steadily to the right on a level road. Tire pressures, tire sizes and brakes are equal on both sides. What is the most likely cause?

  1. More positive camber on the left front wheel than the right.
  2. Less positive caster on the right front wheel than the left.
  3. Slightly more toe-in than specified on both front wheels.
  4. A low fluid level in the power steering reservoir.

Correct answer: Less positive caster on the right front wheel than the left. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

27. The water-in-fuel warning lamp is on. A technician finds the fuel-water separator is full of water. What is done first?

  1. Replace the secondary filter and reset the warning lamp at once.
  2. Add antigel additive to the tank and restart the engine.
  3. Drain the water into a container and dispose of it as required.
  4. Drain and refill the fuel tank before servicing the separator.

Correct answer: Drain the water into a container and dispose of it as required. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

28. A tractor takes four minutes to build pressure from 85 to 100 psi at 700 rpm. A soap test finds no leaks, the gauges are accurate and the governor cuts out correctly. What is the most likely cause?

  1. The compressor is worn or has a restricted discharge line.
  2. The governor cut-out pressure is set far too high.
  3. The low air pressure warning switch is stuck closed.
  4. The trailer supply valve seat is leaking air badly.

Correct answer: The compressor is worn or has a restricted discharge line. The full explanation (why this answer is right, why each of the three other options is wrong, and the National Safety Code section it is based on) comes with Premium access.

29. System voltage reads 15.6 V at 1 500 rpm with the loads off, the specified range is 13.8 V to 14.4 V, and the batteries are hot with low electrolyte. What is the most likely cause?

  1. An open diode in the alternator.
  2. A faulty alternator voltage regulator.
  3. A slipping alternator drive belt.
  4. A high-resistance alternator cable.

Correct answer: A faulty alternator voltage regulator. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

30. A twin-countershaft transmission shifts normally in the low range, but the range will not change to high. The shift lever and linkage move freely. What should be checked next?

  1. The wear pattern on the main shaft bearings and splines.
  2. The tooth contact on the countershaft and main drive gears.
  3. Air pressure at the range cylinder as the selector is moved.
  4. The clearance between the release bearing and clutch brake.

Correct answer: Air pressure at the range cylinder as the selector is moved. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

31. No manufacturer specification is available. A 30 mm spring pin in a front leaf spring shows 4 mm of wear. What is done?

  1. Replace the bushing and reuse the worn pin.
  2. Build up the worn pin by welding and reuse it.
  3. Tighten the shackle nut and recheck the wear.
  4. Replace both the spring pin and the bushing.

Correct answer: Replace both the spring pin and the bushing. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task and the National Safety Code section it is based on) comes with Premium access.

32. A technician finishes adjusting the compression brake clearances and installs the covers. What is verified before the truck is returned to service?

  1. That the retarder applies with the clutch pressed and throttle open.
  2. That the ECM shows no fault codes, with no road test needed.
  3. That the retarder applies at each setting with no cover leaks.
  4. That the engine can run at high idle for an hour with the brake on.

Correct answer: That the retarder applies at each setting with no cover leaks. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

33. A truck battery goes flat after three days parked. With the key off and the modules asleep, a multimeter in series with the negative cable reads 1.8 A against a 0.05 A limit. What is done next?

  1. Replace the alternator because its diodes are leaking current.
  2. Load test the batteries because the draw means they are weak.
  3. Raise the meter range and crank the engine to confirm the draw.
  4. Remove fuses one at a time and watch for the current to drop.

Correct answer: Remove fuses one at a time and watch for the current to drop. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

34. Both front tires of a truck show feathered tread wear, with the ribs smooth on one edge and sharp on the other. What is the most likely cause?

  1. Low inflation pressure in both front tires.
  2. Excessive positive caster on the front axle.
  3. Incorrect toe setting on the front axle.
  4. A worn pitman arm at the steering gear.

Correct answer: Incorrect toe setting on the front axle. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

35. A block heater is plugged into a good 120 V outlet and its cord tests sound, yet the coolant stays cold. How is the heating element tested?

  1. Leave the heater plugged in and read the element resistance with a multimeter.
  2. Unplug the heater and measure the element resistance with a multimeter.
  3. Unplug the heater and measure the element voltage with a multimeter.
  4. Leave the heater plugged in and read the element amperage with a test light.

Correct answer: Unplug the heater and measure the element resistance with a multimeter. The full explanation (why this answer is right, why each of the three other options is wrong, and the RSOS sub-task it is based on) comes with Premium access.

Take the free test ยท full question bank and mock exams with a subscription