What this topic covers
Block F, Steering, Chassis/Frames, Suspensions, Tires, Wheels and Hubs: 18 of the 135 questions, RSOS tasks F-28 to F-32. These are original practice notes, not materials of the Red Seal program. Inspection values come from the National Safety Code standards in force on January 1, 2027 and may vary by province (jurisdictions may vary); adjustment, torque and clearance values always come from the vehicle manufacturer's documentation; the rest is standard trade practice.
Steering (F-28)
- Kingpin play: raise the axle to unload the kingpin, then rock and turn the wheel. Without a manufacturer specification, reject lateral movement over 5 mm (20 in. wheels or larger) or 3 mm (smaller), vertical over 2.5 mm, telescopic column over 6 mm (NSC Standard 11B, section 4.4; jurisdictions may vary).
- Alignment: a steering axle pulls toward the side with less positive caster; more positive camber pulls toward that side; excess toe-in wears tires without a pull.
- Power steering test: low flow points to pump wear, low relief pressure to a relief valve stuck open; good flow and relief with poor assist points to a leak past the gear piston seal.
- Bleeding: engine running, turn slowly lock to lock, then recheck the level; holding the wheels against the stop overheats the fluid.
Frames (F-29)
- Measuring: unequal diagonals with equal widths = out of square; sag with a straight edge; twist by comparing rail heights.
- Repairs: fasteners of the same size and grade, torqued to the manufacturer's value; a repair that does not meet the OEM standard, such as welding, is rejected (NSC Standard 11B, section 8.6).
Suspensions (F-30)
- U-bolts: final torque with the weight on the springs, evenly in a diagonal pattern; loose U-bolts are a reject (NSC Standard 11B, section 2.4; jurisdictions may vary).
- Air suspension: one side sagging means a leak on that side, found with soapy water (section 2.5).
- Shock absorbers: a leaking unit has lost its damping; replace the pair on that axle (section 2.7).
- Walking beam: cross tube bushing clearance over 7 mm on a truck is rejected (section 2.2); replace the bushing.
Fifth wheel and kingpin (F-31)
- Kingpin: rejected when worn more than 3.0 mm, checked with a purpose-made gauge (NSC Standard 11B, section 10.7; jurisdictions may vary).
- Coupling check: gentle tug in low gear against the trailer brakes, then look at the jaws and release handle, before raising the landing gear.
- Fasteners: more than 20 percent ineffective fasteners on a side is a reject; on 12 fasteners, 0.20 × 12 = 2.4, so 3 or more.
- Stiff latch: contaminated or missing lubricant is a reject; clean and grease the plate, jaws and latch.
Tires, wheels and hubs (F-32)
- Tread depth: less than 3 mm on an active steering axle, less than 2 mm on other tires (NSC Standard 11B, section 9.1; some jurisdictions require 3 mm on all tires). No retreads on an active steering axle (section 9.2).
- Duals: diameters differing by more than 13 mm are rejected (section 9.3): 1 056 - 1 040 = 16 mm, so fit a closer match.
- Multi-piece rims: inflate in a restraining cage with a clip-on chuck and a long hose; a tire run flat is demounted before reinflation.
- Wheel nuts: star sequence, in stages, finished with a torque wrench to the manufacturer's value (section 9.11).
- Hub end play: without a specification, reject below 0.02 mm or above 0.13 mm (section 9.6).
Diagnosis and calculation
| Symptom | Likely cause | Check |
|---|
| Pull, equal tires and brakes | Uneven caster | Alignment |
| Noise, foaming, low flow | Restricted suction hose | Pump inlet |
Steering cylinder: F = A × P with A = π × r² (π = 3.14). Radius 25 mm: 3.14 × 25 × 25 = 1 962.5 mm², and at 8 N/mm², F = 15 700 N.
Sample questions (5)
1. An auxiliary power assist cylinder has a piston 50 mm in diameter, and a pressure of 8 MPa (8 N/mm²) acts on the full face of the piston. Using π = 3.14, what force does the pressure produce?
- 628 N
- 1 256 N
- 15 700 N
- 62 800 N
Force equals area times pressure, and the piston area uses the radius squared: 3.14 × 25 × 25 = 1 962.5 mm², and 1 962.5 mm² × 8 N/mm² = 15 700 N (RSOS sub-task F-28.03, hydraulic cylinders). The 628 N value uses the radius without squaring it (3.14 × 25 × 8), and 1 256 N uses the diameter without squaring it. The 62 800 N value squares the diameter instead of the radius.
2. During a periodic inspection under NSC Standard 11B, steering lash is measured on a truck with power steering and a 450 mm steering wheel. Lash greater than what distance is rejected?
- 75 mm of free play
- 87 mm of free play
- 100 mm of free play
- 140 mm of free play
NSC Standard 11B, section 4.3, rejects lash greater than 75 mm on a power steering system with a wheel of 500 mm or less (jurisdictions may vary). The 87 mm value is the hazardous-condition level for the same system, and 100 mm is the reject limit for a manual system with a larger wheel. The 140 mm value is the hazardous level for a manual system.
3. No manufacturer specification is available for kingpin lateral movement on a truck with 22.5 in. wheels. Under NSC Standard 11B, movement greater than what distance, measured at the outer edge of the tire, is rejected?
- 2.5 mm of movement
- 3 mm of movement
- 5 mm of movement
- 6 mm of movement
NSC Standard 11B, section 4.4, rejects lateral kingpin movement of more than 5 mm on wheels 20 in. or larger when no manufacturer specification exists (jurisdictions may vary). The 3 mm value applies to wheels under 20 in., and 2.5 mm is the vertical movement limit. The 6 mm value is the column movement limit for a telescopic steering column.
4. A technician is measuring steering lash on a truck equipped with power steering. How is the truck set up before the measurement?
- Engine stopped and the front wheels turned fully to the left.
- Engine running and the front wheels in the straight-ahead position.
- Engine running and the front wheels turned fully to the right.
- Engine stopped and the front wheels in the straight-ahead position.
NSC Standard 11B, section 4.3, has lash measured on a power steering vehicle with the engine running, beginning with the wheels straight ahead (jurisdictions may vary). With the engine stopped the assist is missing, so the lash reading is not valid for that system. Starting from full lock would not give a reading from the straight-ahead position.
5. A technician is about to check a front axle kingpin for wear. What is done first?
- Remove the wheel and hub to expose the kingpin bushings.
- Disconnect the drag link from the pitman arm on the gear.
- Leave the tires on the floor and rock the steering wheel.
- Raise the axle so that the weight is off the kingpin.
NSC Standard 11B, section 4.4, has the axle raised to unload the kingpin before the wheel is rocked in and out and turned (jurisdictions may vary; RSOS sub-task F-28.01, king pins to be measured). Rocking the steering wheel with the tires on the floor checks the linkage, and the loaded kingpin hides its own play. Removing the hub and disconnecting the drag link are not needed to measure kingpin play.