RedSealTruckExam

🚛 Cabs

What this topic covers

Block G, Cabs: 5 of the 135 questions. RSOS tasks G-33 (cab interior components) and G-34 (cab exterior components).

These are original practice notes, not documents of the Red Seal program. Inspection values come from the National Safety Code standards in force on January 1, 2027, and jurisdictions may vary. Adjustment, torque and clearance values always come from the vehicle manufacturer's documentation. The rest describes standard methods of the trade.

Supplemental restraint system (G-33)

Seats and seat belts (G-33)

Controls and accessories (G-33)

Glass, hood and cab suspension (G-34)

Diagnosis

SymptomLikely causeCheck
Air seat sinksCracked air spring bellowsSoap solution on the air spring
Cab low on both sides, no leaks, normal supplyHeight control valve or linkageValve operation and linkage
Cab tilts to one sideLeaking air bag on that sideSoap solution
Window inoperative, 12 V at motor, good groundFailed or seized motorReplace the motor
Take the free test · full question bank and mock exams with a subscription

Sample questions (5)

1. A technician must replace a switch on a steering column that is next to the driver air bag (SRS) module. What is done first?

  1. Switch the ignition on and clear the stored SRS codes with a scan tool.
  2. Disconnect the battery and wait the time given in the service information.
  3. Probe the air bag connector with a test light to confirm it has no voltage.
  4. Unbolt the air bag module from the wheel and then disconnect the battery.

Air bag modules can deploy if their circuit is energized, so the battery is disconnected and the stored energy is allowed to drain for the time given in the manufacturer's service information. Clearing codes with the ignition on leaves the system live. A test light can pass enough current to fire an inflator, and removing the module before the battery is disconnected risks an accidental deployment.

2. A technician removes a driver air bag module from a steering wheel and sets it on the bench. How is the module placed?

  1. Face down, so that the cover rests on a clean, folded shop cloth.
  2. On its edge, clamped in a vise to keep it from rolling off.
  3. Inside a closed toolbox drawer to protect the soft trim cover.
  4. Face up, with nothing placed on top of or in front of the module.

A removed air bag module is stored face up with nothing on top of or in front of it, so that an accidental deployment does not throw the module or a tool at anyone. Face down, clamped on its edge or sealed in a drawer, the module would be launched or the force trapped if it deployed. RSOS sub-task G-33.03 lists the explosive SRS as a hazard.

3. A driver reports that an air-suspended seat slowly sinks to its lowest position within minutes after it is raised. Soap solution forms bubbles on the seat's air spring. What is the most likely cause?

  1. A cracked air spring is leaking air through the bellows.
  2. A restricted supply line is slowing the seat's inflation.
  3. A worn seat track roller is letting the seat frame drop.
  4. A worn seat shock absorber is letting the seat bounce.

Bubbles in soap solution on the air spring show where the air is escaping, so the cracked bellows is the leak that lets the seat sink; air leak on seat is a symptom listed in RSOS sub-task G-33.02. A restricted supply line slows the seat when it is raised but does not make it sink, a worn shock absorber makes the seat bounce, and a worn track roller affects fore-aft movement, not height.

4. During a periodic inspection under NSC Standard 11B, a technician finds the driver's seat belt webbing frayed along one edge. The buckle latches and the retractor works normally. What is the result?

  1. Pass, because the buckle and the retractor both work normally.
  2. Pass, once the frayed edge is trimmed back and heat sealed.
  3. Reject, because frayed webbing means the belt must be replaced.
  4. Hazardous condition, because the seat belt is inoperative.

NSC Standard 11B, section 8.20 rejects a seat belt whose webbing material is broken, cut, frayed or torn (jurisdictions may vary). A working buckle and retractor do not offset damaged webbing, and trimming and heat sealing is not an approved repair. The belt still latches and retracts, so it is not inoperative, and the hazardous condition for a required seat belt that is inoperative or missing does not apply.

5. A driver-side power window does not move when the switch is pressed. With the switch held, 12 V is measured across the terminals of the connected motor, the ground side drops 0.1 V and the fuse is good. What is the most likely cause?

  1. An open feed wire between the switch and the motor.
  2. A failed window switch with open contacts inside.
  3. A blown fuse in the window motor feed circuit.
  4. A failed motor that does not turn with power applied.

Full battery voltage across the terminals of the connected motor with a low voltage drop on the ground side shows that the switch, fuse, feed wire and ground are all delivering power. A motor that does not turn under those conditions has failed or is seized. A bad switch, an open feed wire or a blown fuse would leave the motor without 12 V; malfunctioning window controls are a symptom listed in RSOS sub-task G-33.02.

Start free

RedSealTruckExam · Topics · Exam guide · Sample questions