What this topic covers
Block E of the Red Seal examination, Drive Trains: 17 of the 135 questions. It covers RSOS tasks E-21 to E-27, from clutches to transmission retarders. These are original practice notes, not documents of the Red Seal program. Inspection values come from the National Safety Code standards in force on January 1, 2027 (jurisdictions may vary). Adjustment, torque and clearance values always come from the vehicle manufacturer's service information; the rest describes standard methods of the trade.
Clutches (E-21)
- Lubrication: cross shafts, linkages and release bearings as specified; friction surfaces stay clean and dry.
- Adjustment: restores the manufacturer's tolerance between the release bearing and the clutch brake as the disc wears (RSOS sub-task E-21.01).
- Slipping with loss of free play: disc wear keeps the release mechanism partly applied and lowers clamp load. Excess free play leaves the disc dragging and the gear grinds: adjust, then recheck.
- Hydraulic release: a spongy pedal means trapped air; bleed the primary and secondary cylinders (RSOS sub-task E-21.03).
Standard transmissions (E-22)
- Synchronizer: uses friction to bring a gear and its shaft to the same speed before engagement.
- Gear ratio: driven teeth / driving teeth for each mesh, overall ratio = product. Example: 50 / 20 = 2.5 and 36 / 24 = 1.5, so 2.5 x 1.5 = 3.75 : 1. Output speed = input speed / ratio: 1 800 rpm / 4.50 = 400 rpm.
- Jumping out of gear with sound linkage: worn engagement teeth, worn fork or weak detent (RSOS sub-task E-22.02).
- No high range: check that air reaches the range cylinder when the selector is moved.
- Twin countershafts: timed by meshing the marked teeth with the marked teeth of the main drive gear (RSOS sub-task E-22.03).
Automatic transmissions and retarders (E-23, E-27)
- Stall test: wheels chocked, parking and service brakes held. Stall speed above specification: slipping clutch pack or low line pressure; below: weak engine or freewheeling stator (RSOS sub-task E-23.02).
- After a rebuild: the oil cooler is flushed and flow tested, or replaced if it stays blocked.
- Fluid level: by the manufacturer's procedure, at operating temperature, after cycling the selector.
- Retarder service: let the unit cool and relieve pressure before opening a fitting; measure coil resistance on a de-energized, isolated coil (RSOS task E-27).
Automated transmissions (E-24)
- Principle: a standard transmission shifted by computer-controlled actuators.
- Learn procedures: a new actuator is calibrated, and a new clutch relearned, by the manufacturer's procedure before the road test (RSOS sub-task E-24.03).
- Incomplete shift: input 1 500 rpm / output 1 000 rpm = 1.5 : 1 when 1.00 : 1 is commanded; suspect a worn synchronizer or stuck shift fork.
Drivelines (E-25)
- Phasing: yokes at both ends in the same plane. A vibration tied to road speed after slip yoke work points to out-of-phase yokes.
- Working angles: nearly equal so the joints cancel; correct the axle pinion angle with shims, then measure again.
- Inspection: vertical movement between opposing yoke ends greater than 3.0 mm is a hazardous condition (NSC Standard 11B, section 1.4; jurisdictions may vary).
Drive axles (E-26)
- Inter-axle differential lock: engaged before the slippery section, at low speed, with no wheel slip. If the cylinder moves under air but the lock fails, suspect the shift fork.
- Tooth pattern: marking paste on the crown gear; a dial indicator measures backlash, a torque wrench pinion bearing preload.
- Torque: ratios are multiplied, not added: 400 N.m x 3.00 x 2.00 = 2 400 N.m.
- Warning signs: a large hardened steel chip on the drain plug calls for opening the axle for diagnosis; seepage that follows temperature points to a blocked breather.
Sample questions (5)
1. A technician is lubricating a clutch control during a scheduled service of a tractor. Which parts are lubricated according to the manufacturer's service information?
- Disc facings, flywheel face and pressure plate surface.
- Cross shafts, linkage pivots and the release bearing.
- Clutch brake facing, disc facings and flywheel face.
- Release springs, disc facings and pressure plate face.
RSOS sub-task E-21.01 calls for lubricating cross shafts, linkages and release bearings as the manufacturer specifies. The disc facings, flywheel face, pressure plate surface and clutch brake facing must stay clean and dry, because lubricant on a friction surface makes the clutch slip or drag. Release springs are not a lubrication point.
2. After a road test, a technician finds that the pedal free play of a manual-adjusting clutch is below the manufacturer's minimum. What is done to correct it?
- Shorten the pedal return spring so that the pedal sits higher at rest.
- Replace the flywheel because it is the part that sets the pedal free play.
- Install a thicker clutch brake to take up the extra clearance in the pedal.
- Adjust the clutch to restore the release bearing to clutch brake gap.
RSOS sub-task E-21.01 describes adjusting the clutch to obtain the manufacturer's tolerance between the release bearing and the clutch brake, which restores free play as the disc wears. A shorter return spring only changes pedal height, the flywheel does not set free play, and a thicker clutch brake would change release clearance without correcting the wear.
3. The manufacturer specifies 25 to 40 mm (1 to 1.5 in.) of clutch pedal free play. A tractor measures 75 mm (3 in.) and grinds when first gear is selected at a stop. What is done next?
- Replace the clutch brake before taking any other measurement.
- Replace the flywheel and the pilot bearing as a matched set.
- Adjust the clutch to the specified free play, and then recheck it.
- Lubricate the release bearing and the cross shaft, then road test.
Excess free play means the release bearing travels too little to free the disc fully, so the input shaft keeps turning and the gear grinds (RSOS sub-task E-21.02). The next step is the adjustment to the manufacturer's specification followed by a recheck. Replacing the clutch brake, flywheel or pilot bearing is premature until the adjustment fails, and lubrication does not change free play.
4. A technician replaces the secondary cylinder on a hydraulic-assisted clutch control. The pedal now feels spongy and the clutch drags. What is done?
- Shorten the pushrod until the pedal travels to the floor.
- Bleed the air from the primary and secondary cylinders.
- Replace the release bearing to remove the spongy pedal feel.
- Set the clutch brake to the minimum clearance listed.
Air trapped in the circuit compresses instead of passing pedal movement to the release bearing, which gives a spongy pedal and incomplete release; bleeding the primary and secondary cylinders is part of RSOS sub-task E-21.03. Shortening the pushrod, replacing the release bearing or resetting the clutch brake does not remove the air.
5. What is the job of a synchronizer in a synchronized manual transmission?
- Match gear speed to the shaft speed before engagement.
- Hold the selected gear in mesh while torque is applied.
- Divide the input torque equally between two countershafts.
- Supply air to the range cylinder when the driver shifts.
A synchronizer uses friction to bring a gear and its shaft to the same speed so the gear engages without clashing; RSOS task E-22 lists synchronizers among the components. Holding a gear in mesh is the job of the detent and shift rail, sharing torque between two countershafts is a feature of the countershaft design, and sending air to the range cylinder is done by the range valve and air lines.