RedSealTruckExam

🚚 Trailers

What this topic covers

Block H of the Red Seal examination, Trailers: 8 of the 135 questions. It covers RSOS tasks H-35 (trailer components: coupling, landing gear, sliding tandem, lift axle, body, floor, rear impact guard, lighting) and H-36 (heating and refrigeration units). These are original practice notes, not documents of the Red Seal program. Inspection values come from the National Safety Code standards in force on January 1, 2027 (jurisdictions may vary). Adjustment, torque and clearance values always come from the vehicle manufacturer's service information; the rest describes standard methods of the trade.

Coupling and landing gear (H-35)

Sliding tandem and lift axle (H-35)

Body, floor and rear impact guard (H-35)

Trailer lighting (H-35)

Refrigeration units (H-36)

Diagnostic links

SymptomLikely causeCheck
High suction, low discharge pressureWorn compressor valvesCompressor
Both pressures highOverchargeRefrigerant charge
Low suction pressureRestricted filter drierFilter drier
High discharge pressureBlocked condenserCondenser
Take the free test · full question bank and mock exams with a subscription

Sample questions (5)

1. Under NSC Standard 11B, section 8.25, a trailer manufactured on or after September 23, 2007 needs a rear impact guard if its GVWR is at least what mass?

  1. 2 268 kg
  2. 3 500 kg
  3. 4 536 kg
  4. 6 350 kg

NSC Standard 11B, section 8.25 requires every trailer with a GVWR of 4 536 kg or greater manufactured on or after September 23, 2007 to be fitted with a rear impact guard that meets CMVSS 223, with listed exceptions (jurisdictions may vary). 2 268 kg is half of that mass (5 000 lb instead of 10 000 lb), and neither 3 500 kg nor 6 350 kg is the threshold named in the note.

2. A dry van trailer backs into a dock and the horizontal member of its rear impact guard is bent downward by 90 mm. The welds are not cracked. What is the result under NSC Standard 11B, and why?

  1. Pass, because multiple bends are permitted in the guard member.
  2. Pass, because no weld on the guard is cracked or broken.
  3. Reject, because any bend in the guard member is a reject condition.
  4. Reject, because the member is bent more than 75 mm downward.

NSC Standard 11B, section 8.25 rejects a rear impact guard whose horizontal member is bent inward, downward, upward or outward beyond 75 mm, and visible damage also calls for an inspection of the trailer frame and floor (jurisdictions may vary). The note that multiple bends are permitted means a bend within 75 mm passes, so not every bend is rejected, but a 90 mm bend is. Intact welds do not offset a bend past the limit.

3. A landing gear crank handle turns freely in both speed ranges with almost no resistance, but the legs do not move. What is the most likely cause?

  1. Stripped gears inside the landing gear gear box.
  2. A bent cross tube binding between the two legs.
  3. A lack of grease on the leg tubes and foot pads.
  4. A bent foot pad pressing against the ground.

A crank that spins with almost no resistance while the legs stay put means the gears no longer transmit torque, which is the stripped gear fault listed in RSOS sub-task H-35.02. A bent cross tube, a lack of lubrication or a bent foot pad all cause binding and a hard-to-turn crank, not free spinning.

4. How is the landing gear of a trailer tested during a periodic inspection under NSC Standard 11B?

  1. Run the legs down and up in the low speed setting.
  2. Operate the legs and handle in each speed setting.
  3. Run the legs down in the high speed setting and stop.
  4. Look over the legs and pads from ground level.

NSC Standard 11B, section 8.22 calls for testing the operation of the landing gear in all speed settings, since a gear box can bind or slip in one range and not the other (jurisdictions may vary). Using one speed setting only, or looking at the legs from ground level, cannot show a binding, inoperative or seized unit.

5. A sliding bogie has 12 locking pins in use. During a periodic inspection under NSC Standard 11B, some of them are found missing or not engaged. What is the smallest number of such pins that creates a hazardous condition?

  1. 1 pin
  2. 3 pins
  3. 4 pins
  4. 6 pins

NSC Standard 11B, section 8.23 lists a hazardous condition when more than one-fourth of the slider locking pins in use are missing or not engaged (jurisdictions may vary). One-fourth of 12 is 12 x 1/4 = 3, so 3 pins is exactly the limit and 4 pins is the first count that is more than one-fourth. A single missing pin is already a reject condition but not a hazardous one, and 6 pins applies the 50 percent figure that the section uses for cracked attachment welds.

Start free

RedSealTruckExam · Topics · Exam guide · Sample questions